SPT-ARM Protocol Translator/Data Concentrator

Applied Systems Engineering, Inc.’s┬áSPT-ARM is a Protocol Translator and Data Concentrator product with one network channel, four serial channels, and a large software library of RTU/IED communication protocols. It provides cost-effective support for a wide array of protocol and data transport applications common in the SCADA industry.

SPT-ARM

SPT-ARM Protocol Translator/Data Concentrator

Applications supported include operating as a data concentrator, translating one protocol to another, adding dual-port capability to an otherwise single-ported device, providing network access to serial-only equipment, and transporting legacy bit-protocols over a frame relay, or similar network.

Designed for operation in a substation environment, the device does not contain disk drives. It operates on input power of 24 to 160 VDC or 110/120 VAC. The serial communication interface supports speeds up to 56 KB for byte protocols and 9600 baud for bit protocols. The Ethernet port supports 10Base-T operation.

Support is available for a large number of serial protocols, including present-day ones such as DNP3 and IEC 60870-5-101, as well as legacy “bit” protocols such as Conitel and CDC. The Ethernet channel can be configured for DNP 3 LAN/WAN, Modbus/TCP, and IEC 60870-5-104. Support of both master/host and remote/slave operations are available for all protocols. Each communication port, serial or network, can be configured for a different protocol as well as for master or remote operations.

SPT-ARM’s software protocol translation “engine” is based on ASE’s protocol library product, a set of field-proven routines that process the protocol unique aspects of data communication messages. The hardware design is based on ASE’s field-proven BCOM8-56K PCI-bus I/O board: a processor based, 8-channel, high-speed, serial communications device used by several SCADA companies as well as other ASE products.

The SPT-ARM Configuration Editor is a graphical based tool for easy and convenient generation of configuration files used by the SPT-ARM Application. Device, and point configuration information is specified through this Windows based utility program and downloaded through the SPT-ARM configuration and maintenance port, or through a network connection.

Picture5

The configuration editor employs standard Windows procedures. An entire data base configuration can be entered and running within a few minutes. Changes to an active database can be downloaded and activated in seconds to minimize the entire configuration test and development process.

During on-line operation, point data and communication statistics are accessible through a standard web browser. More detailed diagnostic and program status information are available through the configuration utility. This can provide valuable information during the initial installation stage, as well as a useful tool for on-going maintenance.

Key features of the SPT-ARM are presented in the following table:

TopicFeatureDescription
CommunicationSerialFour RS-232 ports, one of which can be used for RS-485 operation.
Network10/100 Base-T Ethernet port
MaintenanceSeparate configuration and maintenance port
Web BrowserPoint data values and communication statistics are available for view through a standard Web browser
Software ConfigurationDatabaseOff-line creation via Windows utility, loaded through network or configuration and maintenance port
ProtocolSelectable by channel
Master/Slave ModeSelectable by channel
RTU/point countsCapacity for over 20,000 points and a large number devices
ApplicationsProtocol TranslatorAdd new protocol capabilities to existing devices
Multi-portAllow multi-host access to a single-ported RTU. Each host port can support a different protocol
Network TransportAdd Ethernet access to a serial port. Supports DNP 3 LAN/WAN, IEC 60870-5-104, and Modbus/TCP
Byte TransportTransport legacy bit-protocols over almost any serial communication equipment
Data ConcentratorConcentrate data from three slave channels to one master serial channel, or four slave channels to a LAN/WAN circuit
HardwareProcessorAMD Élan microprocessor
Power24 to 160 VDC or 110/120 VAC (5VDC option available on request) Max 8W.
Temperature0┬░ to 70┬░C operating, -20┬░ to 70┬░C storage
Watchdog TimerAutomatic restart in the event of a fatal hardware or software error
Activity LEDsComplete set of RS-232 and Ethernet signal LEDs plus one software controlled communication status LED per channel
DimensionsSPT-ARM-I (with enclosure)
10.25 in. Wide x 7.5 in. Deep x 2.7 in. High

An evaluation package, including the Configuration Editor and SPT-ARM Application software for use under Windows, is available. Please contact Applied Systems Engineering for more details.

Protocol Support

Available protocols include DNP 3.0 (serial and LAN/WAN), IEC 60870-5-101, and IEC 60870-5-104, in addition to many legacy ones such as Conitel, CDC 1 and 2, Telegyr 8979, Harris 5000/6000, and RP570. Click Here for a full list.